Toho-electronics TTM200 Bedienungsanleitung Seite 200
- Seite / 264
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
48-7009-E 6-52
1) State when no event has occurred
No event occurs when RUN/READY is switched over.
2) Standby state
No event occurs when RUN/READY is switched over.
3) State when an event has occurred (an event occurs when the event moves out from the standby state.)
By switching over from RUN to READY, the event turns to OFF. It goes to 2)standby state.
■ Event function 2 setting (PV abnormality)
SEt05
oUt1
to
SEt11
oUt7
Setting content
Initial value
7
E1F2
to
E7F2
Function
000
**0
Nonexistent
**1
Existent
Add-on function
*0*
None
*1*
Hold
*2*
Delay
*3*
Hold + delay
Control mode interlocking function
0**
All modes
1**
RUN/MAN mode only
2**
RUN mode only
Set the event function 2 (PV abnormality).
Event function 2 is a function to output signals (ON/OFF) from the outputs 1 to 7 that are assigned for the event function 2
when an abnormality is generated in the input 1.
This function is effective when the event function 2 is set to **1.
This function is useful in case of improper setting of the input 1 type, alarming for input improper wiring, disconnection or
short, or start/stop of other systems.
This function can be used when the target connection for the outputs 1 to 7 are set for the event output.
Note Take care that the event function 2 may event-output when input 1 type is being changed.
For the operation range of the event function 1 and each setting value, see section of event function 1 operation on page 6-49.
For the add-on function of the event function 2 and the control mode interlocking setting, see again section of event function 1
operation on page 6-49
Example of PV abnormal setting: In the case of PV Abnormal, No Added Function, Control Mode
Interlock Full Mode, set to “001”.
- User’s Manual 1
- ★ Precautions on safety 2
- ★ Alarm symbols 2
- ★ Other symbols 2
- Warnings 3
- Cautions 3
- ★ Summary notation 4
- ★ Notation of characters 4
- Contents 5
- 6. Parameters 6
- 7. Appendix 6
- 1. Overview 7
- 1.1 Feature 8
- TTM20 9
- ■ Front panel 10
- ■ Key operations 12
- ■ Others 12
- ■ Input section 14
- ■ Output section 15
- ■ Communication function 16
- 1.6 Basic flow of setting 17
- 2. Installation 18
- Panel cutting dimensions 21
- (9 6× n - 3 ) 22
- 3. Wiring 23
- 3.1 Precautions on wiring 24
- 3.2 Terminal arrangement 25
- DI 1 input 28
- DI 2 input 28
- DI 3 input 28
- DI 4 input 28
- 3.3 Wiring to each terminal 29
- TTM-205/209 30
- TTM-207 30
- 48-7009-E 3-13 35
- 3-4 Examples of wiring 37
- ★ Configuration example 38
- ★ Connection configuration 38
- 4. Basic operation 42
- 4.1 Flow of setting mode 43
- ■ Initial screen 44
- 4.2 Basic operation 45
- 48-7009-E 4-5 46
- 48-7009-E 4-6 47
- 48-7009-E 4-7 48
- 48-7009-E 4-8 49
- 48-7009-E 4-9 50
- 48-7009-E 4-10 51
- 48-7009-E 4-11 52
- 48-7009-E 4-12 53
- 48-7009-E 4-13 54
- 48-7009-E 4-14 55
- 48-7009-E 4-15 56
- 48-7009-E 4-16 57
- 48-7009-E 4-17 58
- 48-7009-E 4-18 59
- 48-7009-E 4-19 60
- 48-7009-E 4-21 62
- 48-7009-E 4-22 63
- 4.2.7 How to set outputs 66
- 48-7009-E 4-26 67
- 48-7009-E 4-27 68
- 5. Operating the equipment 71
- 5.3 How to set run settings 74
- 48-7009-E 5-5 75
- 48-7009-E 5-6 76
- 5.3.3 PID control setting 79
- 48-7009-E 5-10 80
- 48-7009-E 5-12 82
- 48-7009-E 5-14 84
- 5.3.5 Indicator setting 85
- 48-7009-E 5-16 86
- 48-7009-E 5-17 87
- 5.3.7 Event setting 88
- 48-7009-E 5-19 89
- 5.3.8 How to set MD/READY 90
- 48-7009-E 5-21 91
- 5.4.2 Self-tuning function 95
- 5.4.3 Mode/manual function 97
- 5.4.4 Bank function 98
- 5.4.5 Timer function 101
- AC line 110
- To equipment 110
- CT input 110
- Load: heater and such 110
- [When normal] 112
- Temperature 115
- MAX. 16 PARAMETER 117
- 16ﾊﾟﾗﾒｰﾀ 117
- SET21 PGF 122
- 48-7009-E 5-55 125
- 48-7009-E 5-60 130
- Wait range 131
- Example for StEPN 3 134
- SV value 135
- 48-7009-E 5-69 139
- Zone threshold setting 140
- Magnified 142
- SET23 ZBNK 143
- Max. 16 parameters 146
- 6. Explanation on parameters 149
- 6.1 Input 1 type setting 150
- 48-7009-E 6-12 160
- 48-7009-E 6-15 163
- 48-7009-E 6-18 166
- Proportional 167
- Deviation 168
- Setting value 168
- Proportional cycle 169
- 48-7009-E 6-31 179
- <Forward operation> 179
- 3 203
- Abnormality 206
- 6.7 DI setting 207
- 6.8 Timer function setting 210
- 6.10 Initial setting 215
- Ｔ Ｔ Ｍ－２ ０ ４ 220
- 48-7009-E 6-74 222
- 0～999（0．0～999．9）（℃） 222
- 48-7009-E 6-75 223
- ■Time Setting 223
- 6.14 PROGRAM SETTING 225
- 48-7009-E 6-78 226
- Threshold 228
- 7. Appendix 232
- 7.1 Product specifications 233
- 48-7009-E 7-3 234
- 48-7009-E 7-4 235
- 48-7009-E 7-5 236
- 48-7009-E 7-6 237
- 48-7009-E 7-7 238
- TTM-204 238
- TTM-205, 207 and 209 238
- 48-7009-E 7-8 239
- 7.2 Accessories 240
- 7.4 Troubleshooting 242
- 48-7009-E 7-12 243
- 7.5 Setting list 244
- 48-7009-E 7-14 245
- 48-7009-E 7-15 246
- 48-7009-E 7-16 247
- 48-7009-E 7-17 248
- 48-7009-E 7-18 249
- 48-7009-E 7-19 250
- 48-7009-E 7-20 251
- 48-7009-E 7-21 252
- 48-7009-E 7-22 253
- 48-7009-E 7-23 254
- 48-7009-E 7-24 255
- 48-7009-E 7-25 256
- 48-7009-E 7-26 257
- 48-7009-E 7-27 258
- 48-7009-E 7-28 259
- 48-7009-E 7-29 260
- 48-7009-E 7-30 261
- 48-7009-E 7-31 262
- 48-7009-E 7-32 263
- 48-7009-E 7-33 264
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern